The 8051 Microcontroller and Embedded Systems, Volume 1For courses teaching the 8051 Microcontoller. This book uses a step-by-step approach to teach the fundamentals of assembly language programming and interfacing of the 8051 microcontroller. It uses many examples to clarify concepts. Simple, concise examples are utilized to show what action each instruction performs, then a sample is provided to show its application. This text provides a comprehensive understanding of the internal organization of the 8051 registers and resources in a way that sheds the student's fear of assembly language. Whether students become designers of stand-alone systems or complex embedded systems, they will find this text a useful resource. |
From inside the book
Results 1-3 of 42
Page 161
Some timers do this by software , some by hardware , and some have both software and hardware controls . The timers in the 8051 have both . The start and stop of the timer are controlled by way of software by the TR ( timer start ) bits ...
Some timers do this by software , some by hardware , and some have both software and hardware controls . The timers in the 8051 have both . The start and stop of the timer are controlled by way of software by the TR ( timer start ) bits ...
Page 222
In other words if the ITO and IT1 are 0 , meaning that the hardware interrupts are low - level triggered , IEO and IE1 are not used at all . The IEO and IE1 bits are used by the 8051 only to latch the high - to - low edge transition on ...
In other words if the ITO and IT1 are 0 , meaning that the hardware interrupts are low - level triggered , IEO and IE1 are not used at all . The IEO and IE1 bits are used by the 8051 only to latch the high - to - low edge transition on ...
Page 232
SECTION 11.3 : PROGRAMMING EXTERNAL HARDWARE INTERRUPTS 33. True or false . A single interrupt is assigned to each of the external hardware interrupts EXO and EX1 . 34. What address in the interrupt vector table is assigned to INTO and ...
SECTION 11.3 : PROGRAMMING EXTERNAL HARDWARE INTERRUPTS 33. True or false . A single interrupt is assigned to each of the external hardware interrupts EXO and EX1 . 34. What address in the interrupt vector table is assigned to INTO and ...
What people are saying - Write a review
Reviews aren't verified, but Google checks for and removes fake content when it's identified
User Review - Flag as inappropriate
I have this book
Contents
CHAPTERS | 1 |
The 8051 Microcontrollers | 23 |
THE 8051 MICROCONTROLLERS 223 Section 1 1 Microcontrollers and Embedded Processors | 24 |
Copyright | |
19 other sections not shown
Other editions - View all
The 8051 Microcontroller and Embedded Systems: Using Assembly and C Mazidi Muhammad Ali No preview available - 2007 |
Common terms and phrases
ACALL ACALL DELAY addr addressing mode ASCII Assembly language baud rate binary bit addresses carry flag Chapter CJNE connected convert data pins decimal decoder discussed DJNZ DPTR EPROM Example execution external interrupt Figure flag bit frequency I/O ports instruction INT1 Intel interfacing interrupt vector table jump latch LCALL LJMP load logic loop machine cycle memory chip memory location microcontroller microprocessor MOV P1 MOV RO MOVX Notice NV-RAM on-chip ROM opcode operand output pointer program counter PSEN pull-up resistors pulse RAM location register bank reset Review Questions SBUF SECTION serial communication SETB TR1 Show signal SJMP Solution square wave stack stepper motor stop bit SUBB subroutine target address TCON timer Timer/counter TMOD transfer transistors True or false voltage Write a program
Bibliographic information
| Title | The 8051 Microcontroller and Embedded Systems, Volume 1 The 8051 Microcontroller and Embedded Systems, Muhammad Ali Mazidi |
| Authors | Muhammad Ali Mazidi, Janice Gillispie Mazidi |
| Edition | illustrated |
| Publisher | Prentice Hall, 2000 |
| Original from | the University of Michigan |
| Digitized | 5 Aug 2011 |
| ISBN | 0138610223, 9780138610227 |
| Length | 435 pages |
| Export Citation | BiBTeX EndNote RefMan |